load-displacement

这句话英语怎么表达比较好
Until the time when medial displacement of the popliteal artery was found,a suspicion of PAES was arised.
我知道arise是不及物动词,没有被动语态,但我想表达的就是这个意思,我该怎么改好呢?

高中物理名词
刚来国外读高中没多久，学物理是不太清楚position和displacement的区别。
d因该就是国内的位移了，position课本的解释是‘which is the distance and direction of an object from a refence point.'某物距定点的距离和方向，这个怎么理解，感觉国内学的时候全都用位移表示的很清楚，ZM凭空多出这么个单位，对应国内教材的名词翻译是什么？

displacement英文名词解释,语言学
displacement英文名词解释,不是翻译

What is the displacement of Earth after a time interval of 365 1/4 day

Distance 和 Displacement 的区别
大概我知道,就是一个有方向,一个没有,具体帮我看一下,涉及到IGCSE的物理书

英语翻译
The Displacement Results Comparison.It shows in the Table.1 that the bridge deck is pressed
on the loading side,whose displacement is down,but the displacement of the bridge deck is up on
the no-loading side.The displacement increases with the increase of the loading.There are smaller
errors between the computer simulation results and the measured results (refer with:Table 1,Table
2).The results above can provide reference for inverting the actual mechanics model of the bridge.
The Shape of Analysis Results Compared with the Calculative Results.The shape of analysis
results is similar to the calculative results (refer with:Fig.9,Fig.10).It shows that the ANSYS
finite element model can reflect the real working state of the bridge by the comparative results
above (refer with:Table 3).The computer model can be used to calculate the bearing capacity of the
single column bridge under the condition of its bearings disengaging.
The Bearing Capacity of the Bridge
In order to calculate the bearing capacity of the bridge,we can use the finite element model to load.
Different loading methods are applied to the finite element mode.According to the counterforce of
the bearing,we can judge whether the bearing is disengaging.

英语翻译
5.2 Load testing
The load-displacement responses measured during first-time load tests on piles S2-S5 are shown in Figure 8(a).A significant increase in the axial capacity (where capacity in defined as the load at which displacement increased with no increase in load) is evident for piles S2.S3 and S5 over a time period of 7 months.Pile S2,which was loaded l day after installation,developed an axial resistance of 344 KN and this increased to 990 KN for pile S5,which was loaded 220 days after installation.Pile S3 was load tested 10 days after installation.However,a problem with the loading frame resulted in the latter stages of the test being delayed until 2 days later (hence the initial load-unload path for pile S3 in Figure 8(a)).After 12 days.pile S3 had an axial capacity of 665 KN.Pile S4,which had the lowest driving resistance,lowest CPT qc profile and highest IFR during final installation was load tested 30 days after driving and had a capacity of 385 KN.Although the pile developed a marginally higher axial resistance than pile S2,the resistance was significantly lower than that developed by piles S3 and S5.
The increase of the tension resistance of piles S2,S3 and S5 is seen to follow a linear trend when plotted against time on a log scale,with the capacity approximately doubling per log cycle in Figure 8(b).This contrasts with the assumed trend given by the IAC line,which assumes a lower rate of aging over the first 10 days.The resistance developed by pile S4 is significantly below this trend line.Because of the differences in the qc values given by CPT S4b,installation blow-count and IFR value,the installation load capacity of this pile is likely to have been lower than the other piles installed at the site.Normal irregularities in site conditions and thus test results are not considered by the authors to be unusual.Predictions of the pile capacities (excluding S4) made using the ICP-05 method,including the IAC,are seen in Figure i8(b) to provide good estimates of the pile resistance developed at 2 and 220 days after driving.However,it is slightly conservative for the medium-term estimates of the 12-day resistance.

与排气量displacement相对应的进气量的英文单词是什么
如题.

请问Ansys中定义滑动摩擦接触时,是不是就是Displacement?
·经常看到说要定义边界条件,但是书上也没说清楚,不是道是不是就是约束?
·另外在做滑动摩擦接触时,实常数中哪些一般需要修改,哪些默认呢?
·在接触向导设置的Basic中,对于滑动摩擦,需要那种Contact Algorithm呢.
·在Solution Controls 里,为什么经常要自己修改时间步长等,请解释一下Number of Substeps,Time increments,以及Frequency相关设置带来的影响.

英语翻译
The cam layout depends on the displacement diagram and on the three main geometric factors,