GASKET CL1500 RJ OVAL RING SS 304 BHN 160 MAX.ASME B16.20 B1

徐yy2022-10-04 11:39:542条回答

GASKET CL1500 RJ OVAL RING SS 304 BHN 160 MAX.ASME B16.20 B16.5

已提交,审核后显示!提交回复

共2条回复
爱泡吧的胖子 共回答了22个问题 | 采纳率100%
1500磅管法兰连接用金属环垫,
椭圆垫圆弧面, 304不锈钢,勃氏硬度BHN最大160,按ASME B16.20及ASME B16.5要求制造验收
RJ = Ring Joint 环连接
1年前
小春1984 共回答了4个问题 | 采纳率
随机抖动
1年前

相关推荐

英语翻译非常抱歉再次打扰你,我们公司非常需要Partition Cover Gasket,能否确认此份订单,以及做一份P
英语翻译
非常抱歉再次打扰你,我们公司非常需要Partition Cover Gasket,能否确认此份订单,以及做一份PROFORMA INVOICE,以便我司安排预付款,
好坏坏坏1年前3
sandlandtt 共回答了26个问题 | 采纳率73.1%
sorry to disturbe you again,but our company needs Partitiion Cover Gasket very much,so would you please affirm this order form and give us a PROFORMA INVOICE so that we can arrange advance payment?thank you!
gasket,packing是什么意思
希飛思1年前1
禾城小记 共回答了23个问题 | 采纳率87%
gasket详细»
英['gæskɪt] 美['ɡæskɪt]
n. [机] 垫圈;[机] 衬垫;束帆索
packing详细»
英['pækɪŋ] 美['pækɪŋ]
n. 包装;填充物
v. 包装;装满;压紧(pack的ing形式)
垫片材质的英文描述:150#,RF,Gasket,Flexitallic Style CG,0.175* wide 30
垫片材质的英文描述:150#,RF,Gasket,Flexitallic Style CG,0.175* wide 304 SS strip w/Flexicarb
filler w/0.125* thk.CS outer gauge ring.这段话能否帮我翻译下.
尘世中游荡的鱼1年前1
沸腾之冰 共回答了13个问题 | 采纳率84.6%
150磅,突面,垫片,福来西公司CG型号,0.175宽304 柔性碳缠绕带,0.125厚碳钢对中环
GASKET,谁能帮我完整解释下下面的意思
GASKET,谁能帮我完整解释下下面的意思
GASKET,CL 300,SPIRAL WOUND 304 SS W/FLEXIBLE GRAPHITE (95% MIN ) FILLER ,CS CENTERING RING AND SS INTERNAL RING,ASME B16.20
yang洋_8261年前1
路宁涵lnh 共回答了18个问题 | 采纳率77.8%
完整的信息为:缠绕式垫片,压力等级CL300,304SS缠绕带/柔性石墨(碳含量最少95%)填料,CS碳钢做中心定位环材料,SS不锈钢为内环材料,垫片标准ASME B16.20
NO INCOMPLETE SPONGE GASKET TO AVOID AIRLEAK
土司垃圾1年前1
xyhy12 共回答了23个问题 | 采纳率95.7%
意思是没有INCOMPLETE海绵垫,以避免气漏
Gasket,Shim and Spacer三个词用作垫片,垫圈使用的时候有什么区别?应该怎么使用.
Gasket,Shim and Spacer三个词用作垫片,垫圈使用的时候有什么区别?应该怎么使用.
Gasket,Shim and Spacer三个词用作垫片,垫圈使用的时候有什么区别?应该怎么使用.
用在螺钉和螺母间的垫片,应该用哪个词.
无本也dd1年前1
lurongkai 共回答了22个问题 | 采纳率90.9%
Gasket 用于法兰之间,垫片的目的是与法兰螺栓等配合形成密封结构,防止内部管道泄露;
Shim 用于调整补偿间隙的垫片,常用不锈钢及软金属,目的是调整空间间隙;
Spacer 用于调整两物体孔隙的垫片,目的是调整间隙;
如果你用螺母的垫片,应该用Washer这个词汇;
以上内容供参考!
Recess holds gasket firmly in place assuring proper placemen
Recess holds gasket firmly in place assuring proper placement翻译
auouda1年前1
407586 共回答了17个问题 | 采纳率88.2%
凹槽紧紧地把胶条固定在适当的位置,以确保正确的放置.
warning1.ensure valve and gasket isand free of any sand part
warning
1.ensure valve and gasket isand free of any sand particles
2.tighten the nuts with fingers first and in a sequeten similar to tighening car tyre
3.the bolts shoul be fairly evenly tightened
4.the bolts are not to be over- tightened
flyeung1年前2
狐狸mm 共回答了20个问题 | 采纳率75%
警告
1.确保阀和密封圈中没有沙质颗粒;
2.先用手拧紧螺母,接下来用类似的方法拧紧卡车轮胎.
3.适度、对称的拧紧螺栓
4.螺栓不能拧得过紧.
only concentric tool marks allowed on gasket surface
卐魔女卍1年前2
tikkkkk 共回答了17个问题 | 采纳率82.4%
字面意思是:只允许带标示的对中工具用于垫片表面.
从实际操作上的意思:是否为对垫片质量测量工具的审核说明?尚不清晰.需要更多信息才完整.
英语翻译warning1.ensure valve and gasket isand free of any sand
英语翻译
warning
1.ensure valve and gasket isand free of any sand particles
2.tighten the nuts with fingers first and in a sequeten similar to tighening car tyre
3.the bolts shoul be fairly evenly tightened
4.the bolts are not to be over- tightened
灭谛拉拉1年前1
nba007007 共回答了14个问题 | 采纳率78.6%
警告
1.确保阀和垫片区没有沙粒
2.首先用手拧紧螺母,然后按照一定顺序拧紧汽车轮胎的螺母
3.螺栓应当均匀紧固
4.螺栓不能拧的过紧
有些词好像打错了,比如sequeten,是不是sequence?
请问 gasket 与 washer 有什么区别?
6zc61年前3
ahywsbe 共回答了23个问题 | 采纳率95.7%
希望以下的信息对你有所帮助
A washer is a thin disk with a hole,usually in the middle.It is normally used to support the load of a threaded fastener.Other uses are as a spacer,spring (belleville,wave washers),wear pad,preload indicating device,and locking device.Rubber washers are also used in taps (valves) where they form the seal that shuts off the flow of liquid or gas.
Washers are usually metal or plastic.High quality capscrews require hardened steel washers to prevent the loss of pre-load after the torque is applied (due to Brinelling).Rubber or fiber gaskets used in taps to stop the flow of water are sometimes referred to colloquially as washers; while they may look similar,however,washers and gaskets are usually made differently and designed for different functions.
Washers are also important for preventing galvanic corrosion,particularly by insulating steel screws from aluminum surfaces.
A gasket is a mechanical seal that serves to fill the space between two objects,generally to prevent leakage between the two objects while under compression.Gaskets are commonly produced by cutting from sheet materials,such as gasket paper,rubber,silicone,metal,felt,fiberglass,or a plastic polymer.Gaskets for specific applications may contain asbestos.It is usually desirable that the gasket be made from a compressible or slightly compressible material such that it tightly fills the space it is designed for,including any slight irregularities.
One of the more desirable properties of an effective gasket in industrial applications for compressed fiber gasket material is the ability to withstand high compressive loads.Most industrial gasket applications involve bolts exerting compression well into the 14 MPa (2000 psi) range or higher.Generally speaking,there are several truisms that allow for best gasket performance.One of the more tried and tested is:"The more compressive load exerted on the gasket,the longer it will last".There are several ways to measure a gasket material's ability to withstand compressive loading.The "hot compression test" is probably the most accepted of these.Most manufacturers of gasket materials will provide or publish these results.
垫片 GASKET FOR 6" RF FLANGE 150 lb x 1.5mm THICK ASME 16.20 C
垫片 GASKET FOR 6" RF FLANGE 150 lb x 1.5mm THICK ASME 16.20 COMPRESSED SYNTHETIC
笑面狼1年前1
苏菲玛索 共回答了14个问题 | 采纳率100%
垫片标准ASME16.20,是6“大小150lb压力等级的RF连接面法兰之间连接密封用的,材料是COMPRESSED SYNTHETIC FIBRE压缩合成纤维,厚度为1.5mm
平垫圈(机械)的英文单词是gasket还是washer
迷奇小子1年前1
明美的明天 共回答了19个问题 | 采纳率89.5%
是washe
管道垫片的描述GASKET,CL150,RF,3.0MM THICK,RING TYPE PTFE,ASME B16.2
管道垫片的描述GASKET,CL150,RF,3.0MM THICK,RING TYPE PTFE,ASME B16.21/B16.5/JOB STD,
297187341年前1
蓝格莹莹的天 共回答了18个问题 | 采纳率77.8%
楼上的大概的意思已经讲了:
美标法兰(ASME B16.5/B16.5),JOB STD型,压力150# 密封面形式为突面(RF),3.0MM厚度,四氟垫片.
你之后问到的B16.21/B16.5与B16.5/B16.5有什么区别吗?B16.5代表的是什么,宽度还是啥?
这个是代表的垫片和法兰的标准,其中ASME B16.21是非金属垫片的标准,B16.5是法兰的标准.