Heat Distortion temp 和 Molding shrinkage 是怎么翻译,请指教

xkl9532022-10-04 11:39:542条回答

已提交，审核后显示！提交回复

书忘记共回答了15个问题 | 采纳率: Heat Distortion Point (Temp)热变形点(温度).
Molding shrinkage 模制件收缩量; 1年前

英语翻译1.distortion due to hydrostatic testing which impairs sa 英语翻译 1.distortion due to hydrostatic testing which impairs satisfactory functional operation of the valve shall be cause for rejection. 2.any visually detectable leakage through the pressure boundary walls,metal seal rings,flexitallic gaskets or other static seals of the valve shall be cause for rejection,regardless of duration of test time 大米小女1年前3: 一条杆棒等身齐共回答了16个问题 | 采纳率81.3%

1.流体静压实验会削弱阀门功能操作的符合要求的程度/满意度,所以它造成的变形将面临驳回.
2.压力围墙、金属密封环,、福莱西密封垫圈或其他静态密封的阀门造成的视觉可发现的的泄漏,均应被弃,不论测试的持续时间是多久
只是从意思上分了下层次,要是你觉得还有那么点意思就从专业角度规范一下用词……
希望能帮上忙哈……

1年前查看全部

DistortionvolumeRobotDistnoisegatepitchbumpybumpybackstartst Distortion volume RobotDist noisegate pitch bumpy bumpyback start stop about 是音乐的！还有一个 Graph 糖豆糖1年前4: 猪子柏嘉共回答了15个问题 | 采纳率80%

Distortion扭曲,变形
volume 书本,容积,音量,体积,大量
RobotDist应该是机器人的一个什么程序吧
noisegate噪音门
pitch程度,投掷,投掷物,音调,投,扎,搭
bumpy颠簸不平的,气流不稳的
bumpyback（应该和上个单词差不多）颠簸不平的,气流不稳的
start开始,启动
stop 停止,终止
about关于,有关

1年前查看全部

英语翻译Thus,the distortion of the temperature coefficient cause 英语翻译 Thus,the distortion of the temperature coefficient caused by the different current is small,so the thermal runaway may not be occurred due to the changes of the recommended ratings;however,the actual operation is to be confirmed by using an experiment or board. cokeman1年前1: ┆莲子┇ 共回答了23个问题 | 采纳率100%

因此,受不同电流（气流/水流）而造成的温度系数失真是非常小的,所以热量可能并不因为所推荐的级别（或指标）改变而流失,利用实验或实际操作或（配电）板已经证实了该实际操作.

1年前查看全部

英语翻译The permitted distortion which may be corrected 英语翻译 The permitted distortion which may be corrected is expressed as per cent strain,and this is the per cent strain which would be present if the part were deflected elastically into its distored position.It should be noted the relationship between per cent strain and residual stress is an empirical relationship and will not accurately define residual stress-For sheet and plate of constant thickness "T" permitted distortion is also expressed as a function of "T" . 立土1年前2: 栀子98 共回答了22个问题 | 采纳率68.2%

可能被矫正的允许形变是以拉力百分率来表示的,同时这也是这个部分弹性的倾入它的形变位子时将呈现的拉力百分率.应该注意到拉力百分率和残余应力之间的关系是一个经验关系（指来源于观察）,并不准确的定义残余应力.对于拥有固定厚度T的薄面和平板,允许形变表示为T的一个函数

1年前查看全部

Specifying Current Source of Harmonic Voltage Distortion 怎么翻 Specifying Current Source of Harmonic Voltage Distortion 怎么翻译? zhangqiubing1年前1: 贫者至之共回答了24个问题 | 采纳率91.7%

指定的XX电流源电压畸变

1年前查看全部