五孔开关插座L N L1 L11 L12 L13如何接线,家里此处只有三根线,两火一零,如何接线?

五孔指的是一个三孔插座、一个两孔插座、一个开关
共用一根火线和一根零线.在线板内,把进火线分接成三根,一根进开关,一根进三孔插座的下边右边的接线柱,一根进二孔插座右边的接线柱.再把零线分成两根,一根接三孔插座左下角的接线柱.一根接二孔插座左边的接线柱.N（零线）L（火线） 左零右火

直接在插座的火线（L）上取电接在开关上,再将开关的出线接在灯上,把灯的零线（N）接上就可以了!

the
This paper is mainly auto leaf spring before the before and after five hole drilling stent multiaxial head combination machine tools design, the multiaxial head is a multiple output with closed transmission box, can use it in the vertical drilling machine drilling, reaming, wring holes and tapping the process such as processing. Because of its simple structure don't need to change both machine tool equipment, less investment, quick effect so adapt to small and medium-sized batch porous parts processing
Auto leaf spring before before four base of support Φ 14.5 after the hole of the base of support 3 Φ 14.5 hole shall also processing according to the arrangement of technology in Z535 with a fixture on the machine can not only four holes before processing stent and processing base for three holes to save more for replacement shaft head auxiliary time reason design a set of two parts will be the multiaxial head processing general. The two parts in shape and size of roughly the same but also have different place, reason need to design a fixture can meet the two parts are clamping and positioning.
In order to improve the efficiency of the common to drill to drill, so the tool will make the necessary design. The results of the production cost saving, that ensure the process quality, improve the production efficiency, increase the workers' safety operation reliability.
The main consideration and solve the following main problems: (1) processing surface requirements of precision and roughness; (2) the production batch; (3) the shape and size of workpiece structure; (4) drilling machine refitted practical possibility. The analysis of the drilling machine be modified to be modified analysis when the main content of the drill include: (1) to analyze the machine is ready to adjust to modified requirements; (2) to investigate and understand the use of machine tools; (3) considering the power of machine tools; (4) analysis modified strength and stiffness of the machine tool.
【 key words 】 combination machine tools multi-axis head gear transmission system group of drill drill template

16A一开五孔的比较容易承受.
你的空调如果是挂机建议只在配电箱上的分路增加一个空气开关作为电源控制即可,在线路的其他地方最好不要增加开关.大电流容易打坏开关.

就是面板上面一个开关,一个两孔插座,一个三孔插座.外表是一样的.双控里面有3个接线柱,单控2个接线柱.双控可以代替单控.一般都是用双控,价格差不多的

如果你的第四个图能正常使用那你的123图现在的接线就有一个问题,你可以按下图接线试试,将123图中的黄线摘掉,然后按我下图连一颗线试试看看是否好用,应该是好用的

如果有接地线,请接在D口

单开五孔的接法http://zhidao.baidu.com/question/389613392.html?oldq=1

火线啦,这个得用连接线,

开关控制灯炮接法：L1进火线,L2出火线至灯具（灯具另一头接一根零线）,插座火线进L,零线过N,接地有就接,没有可不接.
搞定.L3 不用去管他

先把开关上L1和插座上的L搞个线头连起来.然后,开关上的L标志是火线进（红色的那条）,蓝的是零线,进插座上的N标志,插座中间的是接地,接上双色线.OK,完成.如果你的开关没有这些标志,那就恭喜你,买到伪劣产品了.（以上接法,是指开关控制插座的哦）

四线为：火线L,零线N,开关输出火线L1,接地线黄/绿双色 PE
双孔插座孔接线为左零右相（相线就是火线L）
三孔插座孔接线为左下为零线N,右下为相线L,中上为 接地线PE 开关有两接线柱,一头接相线L,另一头接到灯或者用电设备上

如果是一个开关只控制一个灯,只要接入火线到开关的中间线柱,零线直接接灯.
如果是二个开关控制一个灯,把二个开关的上下线柱分别用电线连接.一个开关的中柱接火线,一个接灯线. 零线直接.

只有二根线,不可能达到又能控制开关灯,插座又有电,还少一根零线
墙上就两个线,一根是火线,一根是到灯去的,这二根线接到开关的二个头上就可以控制灯了,但插座有火线没有零线,插座用不了

这样接是正确的,有可能是开关质量问题,或者是接线的时候开关螺丝没有拧紧松动放电过热造成的.

插座后面接线柱边都已注明了,L接火线,N接零线,还有标上接地符号的接双色黄绿地线.

一开五孔+插座面板的连接方法如下.
开关上的L1孔和插座上的L孔接火线.
插座上的N孔接零线,标有接地符合的孔,接地线.
开关标有L11L12的孔接灯的控制线.
如果要求开关控制插座,火线接L1孔,L11孔接插座L孔,其它接线不变.

你的开关盒里面有一根火线两根灯线,还需要一根零线.

根据你的描述来判断,线盒里没有零线,该处只能接开关,不能接插座.