来料检验中判定结果CR\MA\MI分别是什么意思?

IQC is the incoming quality inspection, to do quality confirmation and check on the raw materials, parts or products in the procurement, namely send raw materials orcomponents in the supplier through the way of samplinginspection on the quality, and finally make the judgment of this batch of products is receiving or return.

合格通常用绿色或蓝色表示（更多用绿色）；不合格用红色；涉及可以让步接收的,用黄色

可以用数显高度仪,能测平面度,垂直度,平行度.价格也不贵.

产品标准型号应该是BV 2.5mm2
他的国家标准 GB/T 5023.1-2008
对导体的尺寸要求是符合GB 3956-1997
标准中并没有对导体标称截面积和导体直径的考核具体要求,标准提倡的是导体电阻要求,因为影响导体载流不只是外径尺寸,材料纯度也很重要,好一点的电解铜外径小一些电阻也是符合要求的.所以推荐去当地质监部门送检检测一个20摄氏度导体电阻,就一项即可.检测费大概几十块而已.如果嫌麻烦你就自己测吧,行业一般规定2.5这个规格的测量公差是正负0.04mm,2.5mm2的单线直径是1.78mm,合格范围就是1.74~1.78mm.（但如果是好点电解铜是可以低些的所以建议检测直流电阻项目）.
对于塑料的厚度是有要求的2.5mm2绝缘厚度是0.8mm,任意一点可以小于此厚度但是不能小于0.8*0.9-0.1=0.62mm（这是标准要求的）,也就是可以在电线某一点上有小于0.8大于0.62mm的厚度,所以一般检测电线一周上的六个点,取平均值要大于等于0.8mm即合格,反之不合格.

We found incoming wire insulation in obvious differences in color, normal color is black, but now it seems the abnormal color of wire rod surface is grey.
These abnormal color wire of about 450m, and the abnormal color of wire has now produced the finished product.
I saw the wire color is not described in the specification, but is necessary to maintain consistent wire colors.
Please tell us how to deal with the abnormal color of the finished product.
Thank you!

The material did not comply with the drawing or the sample.the sample color is green,but the actual color is black.Confirmed by YULIY,the material is unqualified.
Please be informed.

严重缺点CR：缺点可能对使用者造成伤害,不符合相关法律法
规或相关安全要求,及其极严重缺点情形；
主要缺点MAJ：造成产品失去其用途、功能,影响产品的耐用性
时,影响产品的外观美感从而影响销售,可能造成消费者退货或
投诉时等情形;
次要缺点MIN：与产品品质标准存在偏差,但不会显著影响产品
的外观、功能或耐用性时,不会造成退货等情形;
不合格品：有任一个上述缺点的单位产品,优先按较严重的缺点
来计不良品的不良类别
1.选择AQL值
2.选择检验水准
3.依据批量及检验水准,依据表14-1决定样本代字
4.决定采用单次、双次或多次抽样计画
5.决定采用正常、加严或减量检验
6.依据上述步骤4与5决定适当的抽样计画表,如表14-2至14-10
所示
7.查阅上述步骤6的抽样计画表,找到步骤1的AQL值与步骤3的
样本代字所对应的样本大小、Ac值与Re值
.你的问题,样本数还是抽取32.

人工版的翻译

Attached file include the implementation schedule of improvement of incoming packaging, which was provided by the supplier. In the view of the alignment by the supplier, logistics and trading, we made the final decision. Some key points highlight as follows:
1. Although the procedures of repackage from some proposals are simplified, they are not feasible due to the minor purchase quantity make new packing expenses increase.
2. Price has been slight changed from most of the plans. Per the result of negotiation with the supplier, we will not adjust the price of new packaging plan.

检测项目根据产品的用途来定,主要分以下几个方面：1.镀层厚度 2.镀层耐磨性,硬度3.盐雾（抗氧化性）4..环保测试（6价铬离子）

Divides the mold line with the thimble trundle to throw over the front.the inspection expects whether to distort and the nickname.processes the art designing trough to overflow the rubber and the drainage opening broken filament.inspection product surface whether to have crushes as well as lacks the rubber,to throw over the front and so on.will inspect the quality products to put in according to the graphical representation direction attracts models in the plate.
相信我!

According to the customer's requirements for incoming design process, is mainly for the stainless steel exhaust pipe senior automobile decorative chromium plating protection -. By providing the information and the plating on environmental protection and saving cost and improving efficiency etc., basic principles, targeted for processing flowsheet design. Before plating processing parts by anodic electric remove oil, oil and acid ultrasound, and electric lift descaling in before activated. Electroplating process using the first part, in order to satisfy the nickel plating impact with stainless steel surface coating adhesion between the requirements, Secondly, namely half of nickel plating layers bright nickel layer/high sulfur nickel layer QuanGuangLiang/coating, the purpose of which is to improve the stainless steel exhaust pipe anticorrosion performance, Again, finally microporous nickel plating chromium plating, in order to achieve customer to exhaust pipe exterior decoration. Finally, the bath formula and technology conditions in detail, and the maintenance methods of bath. Also listed the plating quality testing method, and the product quality standard. Keywords: exhaust pipe, Process design, Chromium plating, Nickel plated

一般工厂检查不需要使用很严格的标准,以下是我在工厂制定的电阻来料检验标准,供参考：
外观：引出脚无生锈或氧化,可焊性强,引脚容易上锡,色环颜色清晰正确,引脚难以焊接的判为重缺陷,其它判轻缺陷
规格：
(阻值)：电阻的标称阻值及功率需符合采购要求.
用万用表的电阻档测量电阻值应符合标称值,其误差在可允许的范围内.根据色环决定.
规格
（功率）：电阻的标称功率需符合采购要求,通过检查标签及查看电阻体积进行判定.
引脚抗拉力：电阻的引脚需具备一定的抗拉力,在使用过程中应确保不会在正常受到的拉力下而造成引脚脱落或断裂,在电阻的2跟引脚之间施加20N±2N的拉力,并持续30秒,引脚不可脱落或断裂.
认证标识：如需要,查看是否有ROHS标签,3C标签及其他必须的标签.

Incoming inspection, we will according to the test standard
to test and check the weight of the products manufacturers to provide
certificate of material to ensure that the use of the original material is
correct.
希望采纳、、、谢谢

首先确定供应商是否同一批次生产,具体可参照外箱上标注生产日期或是送货是否混在一起.如果是同一批次,就像你举得例子,那就800个一起抽检；如果不是同一批次生产,那就分750和50各自抽检.
希望能帮到你一点

允收,拒收的意思.

110减60等于五十,再用五十除以110得到的数就是良率

这个问题太深奥了，如果在5年前，我也许能够帮到你，以前做过QA这块。现在改行了，很多东西都忘记了 。
可以去 6西格玛论坛问问。
杨柳标准网，免费下载各行各业标准，要下载这个标准可以去那里

IQC (Incoming Quality Control) will measure incoming materials' length when they arrive,and further inspection will also be implemented during the manufacture process.At the same time,we will push suppliers to diminish length discrepancy and provide relevant report.
不是逐字逐句翻译的,但是我觉得还是完整的表达了你需要的意思,需要修改的话请说~请给分~!

We produced a lot of defective goods due to the incoming bad material from the supplier.

To meet customers' needs, the color pattern and color difference report have to be offered in the attachment along with the material supply.
专业翻译,请楼主采纳此答案,谢谢!